Backflow Testing Phoenix Property Owners Trust

Armor Fire Pro handles backflow testing Phoenix metro property owners, property managers and irrigation contractors need to keep water service active and cross connection control compliant. We’re a Gilbert based, state certified crew serving Phoenix, Tempe, Mesa, Chandler, Scottsdale and Gilbert, and we test fire line, domestic and irrigation assemblies alike.

Armor Fire Protection Inc provides professional inspection, repair, and installation of Backflow Prevention Devices. We are certified to complete Backflow Testing Services in the state of Arizona.

If you have domestic water service, an irrigation system, or a fire protection system, you most likely already have backflow devices installed on your property. Your local water agency requires that these devices be inspected on a regular basis. Failure to comply with inspection requirements may result in fines and your water service being discontinued. If you have backflow devices installed, set up an appointment to have your devices tested today.

Call for an appointment for service or use the free quote form and we will be in contact with you within 24 hrs. 480-633-5922.

Backflow Testing Phoenix Property Owners Schedule Every Year

Not every backflow preventer is the same assembly. Which one is on your property determines how it’s tested and how often. Here’s what we service across the metro.

Reduced Pressure (RP) Assemblies

The highest level of protection available, used where a backflow event would pose a health hazard, common on fire sprinkler and irrigation supply lines.

Double Check Valve (DCV) Assemblies

Two independent check valves in series, commonly used on fire protection systems where the hazard level allows a lower protection class than RP.

Pressure Vacuum Breakers (PVB)

A common choice for irrigation systems, installed above grade and above the highest sprinkler head it protects.

Atmospheric Vacuum Breakers (AVB)

The simplest assembly type, used on hose bibs and some irrigation zones where continuous pressure isn’t an issue.

Who Needs Backflow Testing

If your property has domestic water, irrigation or a fire protection system, a water agency somewhere requires proof it’s not tested and current. Here’s who we work with most.

Commercial Property Owners

Office buildings, retail centers and mixed use properties typically carry both domestic and fire line backflow assemblies that both need annual testing.

Restaurant and Foodservice Operators

Commercial kitchens run water through equipment that requires its own cross connection protection, separate from the building’s main assembly.

Irrigation and Landscape Contractors

Every irrigation system tied to a potable water supply needs a PVB or RP assembly, tested annually under your city’s program.

HOAs and Multifamily Communities

Shared irrigation and fire protection systems across a community mean multiple assemblies on one annual testing calendar.

Fire Sprinkler System Owners

Any commercial fire sprinkler water supply needs its own backflow assembly, tested on the same annual cycle as the sprinkler certification.

Industrial and Manufacturing Facilities

Process water lines that connect to the municipal supply carry some of the strictest backflow requirements of any property type we service.

Fire Line Backflow vs. Domestic and Irrigation Backflow

Fire Protection System Backflow

Typically a larger RP or DCV assembly on the sprinkler system’s water supply. Tested annually and required as a condition of your fire sprinkler permit and ongoing certification.

Domestic and Irrigation Backflow

Smaller assemblies on irrigation and potable water lines, tested annually under your local water provider’s cross connection control program. Phoenix, Mesa, Chandler and Gilbert each run their own version of this program.

What’s Included in a Backflow Testing Visit

Assembly by Assembly Testing

We identify and test every backflow assembly on your property, fire line, domestic and irrigation, rather than assuming one test covers the whole site.

Written Test Results

Every test gets a written result you can hand to your insurance carrier, your property manager or your water provider without waiting on a callback.

Our Backflow Testing Process

1. Test

Our certified technicians test each assembly against the manufacturer’s specification and the water provider’s required procedure.

2. Report to Water Provider

Passing results get submitted directly to your local water agency, so you’re not stuck chasing paperwork after the test.

3. Repair Failed Assemblies

An assembly that doesn’t pass gets repaired or rebuilt on the spot whenever the parts allow it.

4. Re-Test and Certify

Once repaired, the assembly is re-tested and certified so your water service and fire sprinkler permit both stay in good standing.

Backflow Testing Questions We Hear Most

What happens if I miss my backflow testing deadline?

Most Phoenix metro water agencies will send a notice, then escalate to fines, and in some cases discontinue water service if a required backflow test lapses long enough. It’s far cheaper to keep the annual test current than to deal with a shutoff, and a discontinued fire line backflow assembly can also put your fire sprinkler certification out of compliance at the same time.

Do I need a permit for backflow testing?

Testing itself doesn’t require a permit, but installing or replacing a backflow assembly typically does. We handle the paperwork on install and replacement jobs, whether it’s a fire line assembly tied to your sprinkler permit or a smaller irrigation unit.

Can you test a backflow device on my fire sprinkler line?

Yes. Fire line backflow assemblies are one of the most common devices we test, since almost every commercial fire sprinkler supply has one, and we can schedule that test alongside your annual sprinkler inspection.

Do you handle the paperwork with the water department?

Yes. We submit passing test results directly to your local water provider as part of the service, so the certification is on file without you having to follow up.

Why does backflow testing matter if my water already tastes fine?

Cross connection control isn’t about taste, it’s about pressure. If pressure drops or reverses anywhere on a shared water line, contaminated water from an irrigation system, a fire sprinkler line, or industrial equipment can get pulled back into the potable supply. A working backflow assembly is what stops that from happening, and it’s why every water agency in the Valley requires annual proof it’s still functioning.

Is backflow testing different for a fire sprinkler line than for irrigation?

The principle is the same, but the assembly size and the paperwork trail are different. Fire line assemblies are usually larger RP or DCV units tied to your fire sprinkler permit, while irrigation assemblies are smaller PVB or AVB units tied to your water provider’s cross connection program. We test both and keep the documentation separated so each one is easy to find if you’re ever asked for it.

Backflow Certification Phoenix Water Providers Accept

Backflow certification Phoenix providers will accept has to come from a tester the city recognizes, filed on the form the city uses. Backflow testing Phoenix AZ properties need is annual for nearly every assembly class, and the consequence of missing it is a water shutoff rather than a fine.

Gilbert Backflow Prevention

Gilbert backflow prevention work is our home turf. The shop is in Gilbert, so scheduling here is usually same week.

Tempe Backflow Prevention

Tempe backflow prevention assemblies get the same certified test, the same repair capability on site and the same report filing.

Backflow Testing Across the Phoenix Metro

We serve the greater Phoenix metro from our Gilbert shop: Phoenix, Tempe, Mesa, Chandler, Scottsdale and Gilbert. If your property has a backflow assembly anywhere in the Valley, our certified technicians can test it.

Fire Sprinklers

Your fire sprinkler supply almost always carries a backflow assembly. We service both on the same visit.

View page →

Fire Hydrant Services

Private hydrants share a water supply with fire line backflow assemblies. We test both.

View page →

Fire Alarms & Lights

Detection, monitoring and emergency lighting for the rest of your building.

View page →

Call for an appointment for service or use the free quote form and we will be in contact with you within 24 hrs. 480-633-5922.

Backflow Testing Service Areas Across the Phoenix Metro

Every city files backflow test reports its own way, with its own deadline and its own submission route. Pick your city for the local requirements.

Mesa

Backflow testing and certified test report filing for Mesa property owners.

View page →

Chandler

Backflow testing and certified test report filing for Chandler property owners.

View page →

Gilbert

Backflow testing and certified test report filing for Gilbert property owners.

View page →

Scottsdale

Backflow testing and certified test report filing for Scottsdale property owners.

View page →